Swaby Lobeline

Construction

All Swaby Lobeline Models Feature the Necessary Air Gap Design and are Available with All Sealing Options including API 682 / API676

01

SERIES M AND MR

For Non Corrosive Applications

Ductile Iron Rotor Case, Elastomer coated rotors, Hardened Replaceable Wear Plates (for MR series), and Hardened Reversible Front Cover

Wet End Construction for M and MR

Pump ModelM (For Low Abrasion, Non-Corrosive )MR (For Abrasive, Non-Corrosive)
Part NameMaterialASTMMaterialASTM
Rotor Case with FlangesDuctile IronA536Ductile IronA536
Rotor InsertsDuctile IronA536Ductile IronA536
Rotor CoatingUrethane90 DurometerUrethane90 Durometer
Front Cover ReversibleCarbon SteelAISI 8620 Case hardenedCarbon SteelAISI 8620 Case Hardened
Radial Wear PlatesNot IncludedCarbon SteelAISI 4140 Through Hardened
Rear Wear PlatesNot IncludedCarbon SteelAISI 8620 Case Hardened
Mechanical SealsStainless SteelAISI 316Stainless SteelAISI 316
Shaft Protection SleevesStainless SteelAISI 316Stainless SteelAISI 316

Wet End Options for M and MR (AIR GAP Between Rotor Case and Gear Case)

Part NameDescriptionASTM
Rotor CoatingNitrile 68-70 Dr.
HNBR
VITON
All Metal Carbon SteelAISI4140
Rotor DesignStraight Three LobeAISI4140
Straight Bi-LobeAISI4140
Circumferential Bi LobeAISI4140
Sealing Options (**)Single Mechanical Seal Cartridge Type Front Pullout Flush-LessAISI 316
(All Seals are Furnished with Shaft Protection Sleeve)Single Mechanical Seal Cartridge Type Front Pullout Flushed Type with Flush portsAISI 316
Double Spring Loaded Lip Seal Cartridge Type Front Pullout with Shaft Protection SleeveAISI 316
API 676 and API 682 SealsSingle Mechanical Seals Front Pullout Design with Flush Ports meets API 682 SystemsAISI 316
Double Mechanical Seals Front Pullout Design with Flush Ports meets API 682 SystemsAISI 316

(**) Sealing Options Applicable to All Pump Models.

All Seals are Installed in the Air Gap Between the Gear Case and Rotor Case and can accommodate External Flushing Plans Requirements when Required.

Gear Case Construction

Gear Case Construction Applicable to All Pump Models and Sizes

Part NameDescriptionASTM
Gear CaseCast Iron with Upper and Lower Oil ChambersA48-76 / G30
ShaftsNon - Wetted with Shaft Sleeves for Shaft ProtectionAISI 4340 HT
BearingsPre-Loaded Heavy Duty Duplex taper roller bearings – Qty 4 bearings per shaft/ 8 bearings per pump
Timing GearsCarbon Steel AGMA Rated Mounted at Drive EndAISI 8620
Timing Gears AttachmentSelf-Centering Taper Locking Assembly Keyless design
Bearing IsolatorsStainless Steel with Grease fittingsAISI 316
02

SERIES A AND AR

For Corrosive Applications

Duplex Stainless Steel Wet end including Rotor Case, Rotors, Replaceable Wear Plates (AR only) and Front Cover

Wet End Construction for A and AR

Pump ModelA (For Low Abrasion, Corrosive) note 1AR (For Abrasive, and Corrosive) note 1
Part NameMaterialASTMMaterialASTM
Rotor Case with FlangesDuplex StainlessA743 (CD4-MCU)Duplex StainlessA743 (CD4-MCU)
Rotors Solid Metal (*)Duplex StainlessA182 Gr F51Duplex StainlessA812 Gr F51
Front Cover ReversibleDuplex StainlessA240-S31803Duplex StainlessA240-S31803
Radial Wear PlatesNot IncludedDuplex StainlessA743 (CD4-MCU)
Rear Wear PlatesNot IncludedDuplex StainlessA240 (Duplex 2205)
Mechanical SealsStainless SteelAISI 316Stainless SteelAISI 316
Shaft Protection SleevesStainless SteelAISI 316Stainless SteelAISI 316

Wet End Options for A and AR (AIR GAP Between Rotor Case and Gear Case)

Part NameDescriptionASTM
Rotor CoatingNitrile 68-70 Dr.
HNBR
VITON
Rotor DesignStraight Three LobeAISI4140
Straight Bi-LobeAISI4140
Circumferential Bi LobeAISI4140
Sealing Options (**)Single Mechanical Seal Cartridge Type Front Pullout Flush-LessAISI 316
(All Seals are Furnished with Shaft Protection Sleeve)Single Mechanical Seal Cartridge Type Front Pullout Flushed Type with Flush portsAISI 316
Double Spring Loaded Lip Seal Cartridge Type Front Pullout with Shaft Protection SleeveAISI 316
API 676 and API 682 SealsSingle Mechanical Seals Front Pullout Design with Flush Ports meets API 682 SystemsAISI 316
Double Mechanical Seals Front Pullout Design with Flush Ports meets API 682 Systems

(**) Sealing Options Applicable to All Pump Models.

All Seals are Installed in the Air Gap Between the Gear Case and Rotor Case and can accommodate External Flushing Plans Requirements when Required.

Gear Case Construction

Gear Case Construction Applicable to All Pump Models and Sizes

Part NameDescriptionASTM
Gear CaseCast Iron with Upper and Lower Oil ChambersA48-76 / G30
ShaftsNon - Wetted with Shaft Sleeves for Shaft ProtectionAISI 4340 HT
BearingsPre-Loaded Heavy Duty Duplex taper roller bearings – Qty 4 bearings per shaft/ 8 bearings per pump
Timing GearsCarbon Steel AGMA Rated Mounted at Drive EndAISI 8620
Timing Gears AttachmentSelf-Centering Taper Locking Assembly Keyless design
Bearing IsolatorsStainless Steel with Grease fittingsAISI 316

Matched to Your Application

Every Swaby LOBELINE model features the necessary air gap design and is available with all sealing options including API 682 / API 676. Tell our engineers about your service conditions and we’ll match the wet-end construction, sealing, and rotor configuration to your application.