Features & Benefits

Lobeline Rotary Lobe Pump is designed with features that provide maximum uptime

The AIR GAP DIFFERENCE

Minimum Down Time. Optimum Reliability.

The Lobeline Rotary Lobe Pump features a maintenance-friendly front pullout design that allows a complete in-place wet end rebuild without removing the pump from the baseplate, disconnecting suction or discharge piping, or requiring realignment. This innovative design minimizes downtime, reduces maintenance costs, and returns your system to service faster.

Maintenance Friendly Front Pullout Design Wet End Rebuild

A design that facilitates complete in place wet end rebuild without removing the pump from the baseplate, disconnect suction and discharge piping, or realignment

A

Rotor Case

B

Gear Case

1

Hinged Front Cover

2

Mechanical seals cartridge type with shaft sleeve

3

Rear wear plates, upper and lower

4

Radial wear plates, upper and lower

5

Rotors – Straight design to facilitate removal of one rotor at a time without special tools.

6

Taper locking assemblies to simplify removal and reinstallation of the rotors.

7

Rotor cap with "O" rings


A.
Rotor Case
B.
Gear Case
1.
Hinged Front Cover
2.
Mechanical Seals Cartridge Type with Shaft Sleeve
3.
Rear Wear Plates, Upper and Lower
4.
Radial Wear Plates, Upper and Lower
5.
Rotors – Straight Design
6.
Taper Locking Assemblies
7.
Rotor Cap with O-Rings
A.
Rotor Case
B.
Gear Case
1.
Optional Sealed Gearbox Design: In addition to the front bearing isolator, the timing port plate can be fitted with a labyrinth seal along with sealed expansion caps in place of the traditional vents. These optional features (not shown) allow the gearbox to be fully immersed in flood conditions, or to function in extremely humid environments.
2.
Visible Air Gap Design for true and foolproof separation of the rotor case A from the Gear case
3.
Optional Radial Wearplates: Upper and lower wear plates patented design eliminate casing replacement. Retained via a series of externally-sealed fasteners which allow pump to be serviced in place.
4.
Taper Locking Assemblies: Used on rotors and gears to simplify removal and refitting.
5.
Timing Port Plate: Located at the drive end, it permits easy entry to the taper locking assembly (eliminating the need to remove the gearcase cover), allowing pump to be re-timed in the event of a blockage within the pump casing. No more worries about oil drain-down!
6.
Different Sealing Options, Cartridge Type Front Pullout with Shaft Protection Sleeves.
7.
Labyrinth Bearing Isolator: Stainless steel construction eliminates ingress of liquid into the gearbox. Double-lip oil seal retains oil; grease nipple allows grease input to act as barrier within the labyrinth. Functions in static or running state.
8.
Optional Rear Wearplates: Upper and lower plates to protect casing. Retained via a series of externally-sealed fasteners.
9.
Front-Loading Seal Area: Allows the hardened shaft sleeves or mechanical seals to be removed cartridge style through the front of the pump—without removal of the casing.
10.
Hinged Front Cover
11.
Straight Lobe Design benefits: Low NPSH r, Superior Performance, better non compressible solids handling capability.
12.
Heavy Duty Duplex Roller bearings per load point for longer bearing life.
13.
Upper Oil Chamber to ensure lubrication of the upper bearings at low speed
14.
Lower Oil Chamber for lower bearings and continued timing gears lubrication
15.
Heavy Duty AGMA quality timing gear accessible for timing without having to drain the gear case.
16.
Dual Oil Breathers / Oil Filler Cap with Sealed Expansion to prevent moisture and dirt from entering the gear case
1
OPTIONAL SEALED GEARBOX DESIGN

In addition to the front bearing isolator, the timing port plate can be fitted with a labyrinth seal along with sealed expansion caps in place of the traditional vents. These optional features (not shown) allow the gearbox to be fully immersed in flood conditions, or to function in extremely humid environments.

16
Dual Oil Breathers / Oil Filler Cap with Sealed Expansion to prevent moisture and dirt from entering the gear case
2
Visible Air Gap Design for true and foolproof separation of the rotor case A from the Gear case
12
Heavy Duty Duplex Roller bearings per load point for longer bearing life.
B
Gear Case
3
OPTIONAL RADIAL WEARPLATES

Upper and lower wear plates patented design eliminate casing replacement. Retained via a series of externally-sealed fasteners which allow pump to be serviced in place.

A
Rotor Case
11
Straight Lobe Design benefits

Low NPSH r, Superior Performance, better non compressible solids handling capability.

4
TAPER LOCKING ASSEMBLIES

Used on rotors and gears to simplify removal and refitting.

5
TIMING PORT PLATE

Located at the drive end, it permits easy entry to the taper locking assembly (eliminating the need to remove the gearcase cover), allowing pump to be re-timed in the event of a blockage within the pump casing. No more worries about oil drain-down!

15
Heavy Duty AGMA quality timing gear accessible for timing without having to drain the gear case.
6
Different Sealing Options, Cartridge Type Front Pullout with Shaft Protection Sleeves.
7
LABYRINTH BEARING ISOLATOR

Stainless steel construction eliminates ingress of liquid into the gearbox. Double-lip oil seal retains oil; grease nipple allows grease input to act as barrier within the labyrinth. Functions in static or running state.

14
Lower Oil Chamber for lower bearings and continued timing gears lubrication
13
Upper Oil Chamber to ensure lubrication of the upper bearings at low speed
8
OPTIONAL REAR WEARPLATES

Upper and lower plates to protect casing. Retained via a series of externally-sealed fasteners.

9
FRONT-LOADING SEAL AREA

Allows the hardened shaft sleeves or mechanical seals to be removed cartridge style through the front of the pump—without removal of the casing.

10
Hinged Front Cover

Heavy-Duty Rotary Lobe Pumps for All Applications

LOBELINE™ is designed for superior pumping capabilities in a wide range of industrial applications. Choose from 8 models, each available in 12 sizes to suit a variety of operating conditions. Both bare pump and complete pump and drive packages are available. With interchangeable seal arrangements and a selection of wet end metallurgies and designs for your specific application, LOBELINE offers the perfect engineered pumping solution to meet your needs.

Lobeline™ is a Positive Displacement Pump with the following
operational features:

Pump Runs Dry

Non-contacting pumping elements allow periodic use without fluid. Excellent for fluid transfers from tank to tank. Requires no flow indication equipment as used on Screw (Progressive Cavity) pumps that would seize and malfunction if run dry.

Low Shear Action

Smooth tri-lobe geometry provides gentle rolling action enabling shear sensitive fluids to be pumped with minimal damage.

Reversible Flow

Ability to utilize pump in both directions excellent for purging lines or changing pumping system requirements enabling greater process control.

Gas/Air Entrained Fluids

Lobe design can easily handle fluid containing gas/air. Centrifugal pumps are low on efficiency and are prone to losing prime.

Pump Jamming

With LOBELINE simply remove the front cover plate to inspect or clear the pump blockage. Many other pump types such as Screw (Progressive Cavity), Flexible Member (Hose), Plunger, Diaphragm if jammed require substantial disassembly to simply inspect or clear blockages.

Solids Handling

Ability to handle incompressible solids up to 31⁄2″ (90mm) suspended within the fluid.

Metering/Controlled Flow

Provides smooth predictable flow with minimal pulsation or surging when faced with varying pressures. Does not require pulsation dampeners like Plunger, Diaphragm type pumps.

Power Consumption Expense

Lobe pumps require less power due to the non-contacting design. Screw (Progressive Cavity) due to their design require higher start up and running horsepower. Centrifugal pumps require increased power on viscosities greater than 300-500 cps.

Pump Installation Space Problem

Lobe pumps require substantially less floor space than traditional Screw (Progressive Cavity) and Plunger type pumps.

We’re just a message or call away!

Feel free to reach out to us! Our team is here to provide expert guidance and answer any questions you may have about our high-quality rotary pumps.